[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.10.73 (vagrant@vagrant-ubuntu-trusty-64) (gcc version 5.2.1 20151005 (Linaro GCC 5.2-2015.11-2) ) #1 PREEMPT Fri Jun 30 01:13:36 UTC 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Ambarella S2L (Flattened Device Tree), model: Ambarella S2LM Kiwi Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Ambarella: AHB = 0xe0000000[0xe0000000],0x01000000 0 [ 0.000000] Ambarella: APB = 0xe8000000[0xe8000000],0x01000000 0 [ 0.000000] Ambarella: PPM = 0x00000000[0xdfe00000],0x00200000 9 [ 0.000000] Ambarella: AXI = 0xf0000000[0xf0000000],0x00030000 0 [ 0.000000] Ambarella: DRAMC = 0xdffe0000[0xef000000],0x00020000 0 [ 0.000000] Ambarella: DBGBUS = 0xec000000[0xec000000],0x00200000 0 [ 0.000000] Ambarella: DBGFMEM = 0xee000000[0xee000000],0x01000000 0 [ 0.000000] Ambarella: IAVMEM = 0x09000000[ ],0x07000000 [ 0.000000] Ambarella: FBMEM = 0x09000000[ ],0x00000000 [ 0.000000] On node 0 totalpages: 36352 [ 0.000000] free_area_init_node: node 0, pgdat 805bf12c, node_mem_map 805f7000 [ 0.000000] Normal zone: 284 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 36352 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 36068 [ 0.000000] Kernel command line: ubi.mtd=bak root=ubi0:rootfs rw rootfstype=ubifs init=/linuxrc [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 142MB = 142MB total [ 0.000000] Memory: 137872k/137872k available, 7536k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0x89000000 - 0xff000000 (1888 MB) lowmem : 0x80000000 - 0x88e00000 ( 142 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x805564f4 (5434 kB) .init : 0x80557000 - 0x8057d7a4 ( 154 kB) .data : 0x8057e000 - 0x805c7628 ( 294 kB) .bss : 0x805c7628 - 0x805f2c34 ( 174 kB) [ 0.000000] NR_IRQS:240 [ 0.000000] sched_clock: 32 bits at 54MHz, resolution 18ns, wraps every 79536ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000832] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) [ 0.059930] pid_max: default: 32768 minimum: 301 [ 0.060063] Mount-cache hash table entries: 512 [ 0.062878] CPU: Testing write buffer coherency: ok [ 0.063212] Setting up static identity map for 0x803f7d90 - 0x803f7df8 [ 0.065733] devtmpfs: initialized [ 0.067046] pinctrl core: initialized pinctrl subsystem [ 0.067315] NET: Registered protocol family 16 [ 0.068107] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.068638] Ambarella power management: Wed Aug 10 2016 [ 0.068699] L310 cache controller enabled [ 0.068723] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32020000, Cache size: 131072 B [ 0.070370] ambarella-pinctrl e8009000.pinctrl: Ambarella pinctrl driver registered [ 0.070787] ambarella-gpio gpio.0: Ambarella GPIO driver registered [ 0.074880] bio: create slab at 0 [ 0.075971] ambarella-dma e0005000.dma: Ambarella DMA Engine [ 0.076422] SCSI subsystem initialized [ 0.076668] usbcore: registered new interface driver usbfs [ 0.076742] usbcore: registered new interface driver hub [ 0.076922] usbcore: registered new device driver usb [ 0.078106] ambarella-i2c e8003000.i2c: Ambarella I2C adapter[0] probed! [ 0.078706] ambarella-i2c e8007000.i2c: Ambarella I2C adapter[2] probed! [ 0.079738] cfg80211: Calling CRDA to update world regulatory domain [ 0.079814] cfg80211: World regulatory domain updated: [ 0.079835] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.079864] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (2000 mBi, 0 mBm) [ 0.079890] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 0.079915] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 0.080022] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 0.080052] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 0.080077] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2000 mBi, 0 mBm) [ 0.080102] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 0.080126] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 0.080719] Switching to clocksource ambarella-cs-timer [ 0.087927] ambarella-sd e0002000.sdmmc0: Slot0 use bounce buffer[0x88740000<->0x08940000] [ 0.087984] ambarella-sd e0002000.sdmmc0: Slot0 req_size=0x00020000, segs=32, seg_size=0x00020000 [ 0.088016] ambarella-sd e0002000.sdmmc0: Slot0 use ADMA [ 0.160883] ambarella-sd e0002000.sdmmc0: 1 slots @ 50000000Hz [ 0.161066] NET: Registered protocol family 2 [ 0.164985] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.165093] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.165146] TCP: Hash tables configured (established 2048 bind 2048) [ 0.165227] TCP: reno registered [ 0.165252] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.165284] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.165473] NET: Registered protocol family 1 [ 0.165833] RPC: Registered named UNIX socket transport module. [ 0.165868] RPC: Registered udp transport module. [ 0.165927] RPC: Registered tcp transport module. [ 0.165948] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.166396] ambarella-adc e801d000.adc: Ambarella ADC driver init [ 0.167148] audit: initializing netlink socket (disabled) [ 0.167221] type=2000 audit(0.159:1): initialized [ 0.168553] jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. [ 0.168723] msgmni has been set to 269 [ 0.170324] NET: Registered protocol family 38 [ 0.170449] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.170485] io scheduler noop registered [ 0.170502] io scheduler deadline registered [ 0.170531] io scheduler cfq registered (default) [ 0.171709] e8005000.uart: ttyS0 at MMIO 0xe8005000 (irq = 9) is a ambuart [ 0.172117] ambarella-uart e0032000.uart: Serial[1] use txdma [ 0.172156] ambarella-uart e0032000.uart: Serial[1] use rxdma [ 0.172189] e0032000.uart: ttyS1 at MMIO 0xe0032000 (irq = 25) is a ambuart [ 0.173050] brd: module loaded [ 0.175749] loop: module loaded [ 0.178361] ambarella-nand e0001000.nand: in ecc-[1]bit mode [ 0.178398] ambarella_nand: Use On Flash BBT [ 0.178518] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xda (GigdDevice NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 [ 0.178784] Bad block table found at page 131008, version 0x43 [ 0.178972] Bad block table found at page 130944, version 0x43 [ 0.179152] nand_read_bbt: bad block at 0x000000020000 [ 0.179174] nand_read_bbt: bad block at 0x000000040000 [ 0.179194] nand_read_bbt: bad block at 0x000000ea0000 [ 0.179211] nand_read_bbt: bad block at 0x000000ec0000 [ 0.179228] nand_read_bbt: bad block at 0x000000ee0000 [ 0.179244] nand_read_bbt: bad block at 0x000000f00000 [ 0.179260] nand_read_bbt: bad block at 0x000000f20000 [ 0.179277] nand_read_bbt: bad block at 0x000000f40000 [ 0.179293] nand_read_bbt: bad block at 0x000000f60000 [ 0.179309] nand_read_bbt: bad block at 0x000000f80000 [ 0.179326] nand_read_bbt: bad block at 0x000000fa0000 [ 0.179342] nand_read_bbt: bad block at 0x000000fc0000 [ 0.179359] nand_read_bbt: bad block at 0x000000fe0000 [ 0.179375] nand_read_bbt: bad block at 0x000001000000 [ 0.179392] nand_read_bbt: bad block at 0x000001020000 [ 0.179408] nand_read_bbt: bad block at 0x000001040000 [ 0.179424] nand_read_bbt: bad block at 0x000001060000 [ 0.179441] nand_read_bbt: bad block at 0x000001080000 [ 0.179457] nand_read_bbt: bad block at 0x0000010a0000 [ 0.179473] nand_read_bbt: bad block at 0x0000010c0000 [ 0.179489] nand_read_bbt: bad block at 0x0000010e0000 [ 0.179506] nand_read_bbt: bad block at 0x000001100000 [ 0.179522] nand_read_bbt: bad block at 0x000001120000 [ 0.179538] nand_read_bbt: bad block at 0x000001140000 [ 0.179555] nand_read_bbt: bad block at 0x000001160000 [ 0.179571] nand_read_bbt: bad block at 0x000001180000 [ 0.179587] nand_read_bbt: bad block at 0x0000011a0000 [ 0.179604] nand_read_bbt: bad block at 0x0000011c0000 [ 0.179620] nand_read_bbt: bad block at 0x0000011e0000 [ 0.179636] nand_read_bbt: bad block at 0x000001200000 [ 0.179652] nand_read_bbt: bad block at 0x000001220000 [ 0.179669] nand_read_bbt: bad block at 0x000001240000 [ 0.179685] nand_read_bbt: bad block at 0x000001260000 [ 0.179701] nand_read_bbt: bad block at 0x000001280000 [ 0.179717] nand_read_bbt: bad block at 0x0000012a0000 [ 0.179734] nand_read_bbt: bad block at 0x0000012c0000 [ 0.179750] nand_read_bbt: bad block at 0x0000012e0000 [ 0.179766] nand_read_bbt: bad block at 0x000001300000 [ 0.179783] nand_read_bbt: bad block at 0x000001320000 [ 0.179799] nand_read_bbt: bad block at 0x000001340000 [ 0.179815] nand_read_bbt: bad block at 0x000001360000 [ 0.179832] nand_read_bbt: bad block at 0x000001380000 [ 0.179848] nand_read_bbt: bad block at 0x0000013a0000 [ 0.179864] nand_read_bbt: bad block at 0x0000013c0000 [ 0.179880] nand_read_bbt: bad block at 0x0000013e0000 [ 0.179897] nand_read_bbt: bad block at 0x000001400000 [ 0.179913] nand_read_bbt: bad block at 0x000001420000 [ 0.179929] nand_read_bbt: bad block at 0x000001440000 [ 0.179946] nand_read_bbt: bad block at 0x000001460000 [ 0.179962] nand_read_bbt: bad block at 0x000001480000 [ 0.179978] nand_read_bbt: bad block at 0x0000014a0000 [ 0.179994] nand_read_bbt: bad block at 0x0000014c0000 [ 0.180011] nand_read_bbt: bad block at 0x0000014e0000 [ 0.180027] nand_read_bbt: bad block at 0x000001500000 [ 0.180043] nand_read_bbt: bad block at 0x000001520000 [ 0.180060] nand_read_bbt: bad block at 0x000001540000 [ 0.180076] nand_read_bbt: bad block at 0x000001560000 [ 0.180092] nand_read_bbt: bad block at 0x000001580000 [ 0.180109] nand_read_bbt: bad block at 0x0000015a0000 [ 0.180125] nand_read_bbt: bad block at 0x0000015c0000 [ 0.180142] nand_read_bbt: bad block at 0x0000015e0000 [ 0.180158] nand_read_bbt: bad block at 0x000001600000 [ 0.180174] nand_read_bbt: bad block at 0x000001620000 [ 0.180191] nand_read_bbt: bad block at 0x000001640000 [ 0.180207] nand_read_bbt: bad block at 0x000001660000 [ 0.180223] nand_read_bbt: bad block at 0x000001680000 [ 0.180343] 10 ofpart partitions found on MTD device amba_nand [ 0.180366] Creating 10 MTD partitions on "amba_nand": [ 0.180390] 0x000000000000-0x000000020000 : "bst" [ 0.182277] 0x000000020000-0x000000160000 : "bld" [ 0.182976] 0x000000160000-0x0000002a0000 : "ptb" [ 0.183645] 0x0000002a0000-0x0000006a0000 : "spl" [ 0.184326] 0x0000006a0000-0x000000ea0000 : "pba" [ 0.185029] 0x000000ea0000-0x0000016a0000 : "pri" [ 0.185750] 0x0000016a0000-0x0000020a0000 : "sec" [ 0.186469] 0x0000020a0000-0x000008ea0000 : "bak" [ 0.187266] 0x000008ea0000-0x00000fca0000 : "lnx" [ 0.188101] 0x00000fca0000-0x00000fea0000 : "add" [ 0.189063] ambarella-pinctrl e8009000.pinctrl: pin io34 already requested by e0032000.uart; cannot claim for e0020000.spi [ 0.189121] ambarella-pinctrl e8009000.pinctrl: pin-34 (e0020000.spi) status -22 [ 0.189152] ambarella-pinctrl e8009000.pinctrl: could not request pin 34 on device e8009000.pinctrl [ 0.189184] ambarella-spi e0020000.spi: Error applying setting, reverse things back [ 0.189263] ambarella-spi e0020000.spi: DMA is used [ 0.189568] ambarella-spi e0020000.spi: Ambarella spi controller 0 created. [ 0.189823] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.189854] ehci-ambarella: AMBARELLA-EHCI Host Controller driver [ 0.191044] ambarella-ehci e0018000.ehci: EHCI Host Controller [ 0.191112] ambarella-ehci e0018000.ehci: new USB bus registered, assigned bus number 1 [ 0.191334] ambarella-ehci e0018000.ehci: irq 39, io mem 0xe0018000 [ 0.210818] ambarella-ehci e0018000.ehci: USB 2.0 started, EHCI 1.00 [ 0.210931] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.210962] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.210992] usb usb1: Product: EHCI Host Controller [ 0.211013] usb usb1: Manufacturer: Linux 3.10.73 ehci_hcd [ 0.211033] usb usb1: SerialNumber: AmbUSB [ 0.211553] hub 1-0:1.0: USB hub found [ 0.211604] hub 1-0:1.0: 2 ports detected [ 0.211879] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.212065] ambarella-ohci e0019000.ohci: Ambarella OHCI [ 0.212118] ambarella-ohci e0019000.ohci: new USB bus registered, assigned bus number 2 [ 0.212180] ambarella-ohci e0019000.ohci: irq 44, io mem 0xe0019000 [ 0.274876] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.274914] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.274944] usb usb2: Product: Ambarella OHCI [ 0.274964] usb usb2: Manufacturer: Linux 3.10.73 ohci_hcd [ 0.274985] usb usb2: SerialNumber: AmbUSB [ 0.275530] hub 2-0:1.0: USB hub found [ 0.275581] hub 2-0:1.0: 2 ports detected [ 0.276248] ambarella-rtc e8015000.rtc: rtc core: registered rtc-ambarella as rtc0 [ 0.276421] i2c /dev entries driver [ 0.277102] ambarella-wdt e800c000.wdt: Ambarella Watchdog Timer Probed. [ 0.277491] TCP: cubic registered [ 0.277519] Initializing XFRM netlink socket [ 0.277583] NET: Registered protocol family 10 [ 0.278167] NET: Registered protocol family 17 [ 0.278256] Key type dns_resolver registered [ 0.278339] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.278376] ThumbEE CPU extension supported. [ 0.279766] UBI: attaching mtd7 to ubi0 [ 0.530819] hub 1-0:1.0: over-current condition on port 2 [ 0.563139] UBI: scanning is finished [ 0.569350] UBI: attached mtd7 (name "bak", size 110 MiB) to ubi0 [ 0.569394] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 0.569417] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 0.569440] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 0.569461] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0 [ 0.569480] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 0.569504] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1089513100 [ 0.569533] UBI: available PEBs: 0, total reserved PEBs: 880, PEBs reserved for bad PEB handling: 40 [ 0.569609] ambarella-rtc e8015000.rtc: setting system clock to 1970-01-14 06:43:31 UTC (1147411) [ 0.570243] UBI: background thread "ubi_bgt0d" started, PID 45 [ 0.570747] UBIFS: background thread "ubifs_bgt0_0" started, PID 46 [ 0.603200] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 0.603249] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 0.603283] UBIFS: FS size: 104755200 bytes (99 MiB, 825 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) [ 0.603313] UBIFS: reserved for root: 0 bytes (0 KiB) [ 0.603338] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 4F57C051-E695-45BC-9636-B4D88C4988E7, small LPT model [ 0.604040] VFS: Mounted root (ubifs filesystem) on device 0:12. [ 0.605354] devtmpfs: mounted [ 0.605569] Freeing unused kernel memory: 152K (80557000 - 8057d000) [ 1.150868] hub 2-0:1.0: over-current condition [ 1.528203] dsp: module license 'Proprietary' taints kernel. [ 1.528248] Disabling lock debugging due to kernel taint [ 1.529223] dsp_drv_probe_status(713): DSP probe op mode [3], enc mode [7]. [ 1.556561] systemd-journald[64]: [/etc/systemd/journald.conf:11] Failed to parse storage setting, ignoring: memory [ 1.568507] Vout notice: vout0:0 probed! [ 1.568901] Vout notice: vout1:1 probed! [ 1.591580] img: IMG KERN VIRT: WR [0x891f9000, 184 KB], RD [0x87f20000, 36 KB]. [ 1.788806] wm8974_amb.c :: __init wm8974_modinit(void) [ 1.802227] wm8974 audio codec is provided by amba Wu Dongge [ 1.811886] snd_soc_card_amba sound.3: wm8974-hifi <-> e001a000.i2s mapping ok [ 1.879800] iav_drv_probe_status(301): IAV probe status [255], dsp enc mode [3]. [ 1.903662] hw_pts_init(122): HW timer for pts is enabled. [ 1.903695] hw_pts_init(129): Audio clock freq: 12288000, HW timer clock freq: 90000! [ 1.916264] VIN: vin0: probed! [ 1.916319] VIN: vin1: probed! [ 1.931763] dsplog dev init done, dev_id = 248:249. [ 1.932886] dsplog_printk: DSP log by Timer New [ 1.952678] amba_debug_init 248:248. [ 1.956696] Vout notice: CVBS:0@1 probed! [ 1.959569] Vout notice: DBus-All:1@0 probed! [ 2.114537] dhd_module_init: in [ 2.114602] ======== bcm_wlan_set_plat_data ======== [ 2.114622] dhd_wifi_platform_load: Enter [ 2.114659] Power-up adapter 'DHD generic adapter' [ 2.114737] wifi_platform_set_power = 1 [ 2.114756] ======== PULL WL_REG_ON[93], active[1], HIGH! ======== [ 2.288700] systemd-udevd[87]: starting version 215 [ 2.590872] wifi_platform_bus_enumerate device present 1 [ 2.590919] ======== Card detection to detect SDIO card! Slot.num[0] ======== [ 2.706799] mmc0: queuing unknown CIS tuple 0x80 (2 bytes) [ 2.708422] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) [ 2.710017] mmc0: queuing unknown CIS tuple 0x80 (3 bytes) [ 2.715588] mmc0: queuing unknown CIS tuple 0x80 (7 bytes) [ 2.722004] ambarella-udc e0006000.udc: ambarella_udc: version 12 August 2015 [ 2.773104] mmc0: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.773189] mmc0: new high speed SDIO card at address 0001 [ 2.797666] bcmsdh_register: register client driver [ 2.797839] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter [ 2.797969] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter [ 2.797995] bus num (host idx)=0, slot num (rca)=1 [ 2.798013] found adapter info 'DHD generic adapter' [ 2.798341] dhdsdio_probe : no mutex held. set lock [ 2.798481] F1 signature read @0x18000000=0x1602a94c [ 2.805073] F1 signature OK, socitype:0x1 chip:0xa94c rev:0x2 pkg:0x0 [ 2.808022] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 2.814767] dhd_conf_set_chiprev: chip=0xa94c, chiprev=2 [ 2.818154] dhd_conf_read_roam_params: roam_off = 1 [ 2.818204] dhd_conf_read_roam_params: roam_off_suspend = 1 [ 2.821930] input: AmbIR as /devices/virtual/input/input0 [ 2.821992] ambarella-ir e8006000.ir: Invalid keymap! [ 2.822189] ambarella-ir: probe of e8006000.ir failed with error -2 [ 2.829832] wl_create_event_handler(): thread:wl_event_handler:6c started [ 2.830161] tsk Enter, tsk = 0x8764135c [ 2.839260] dhd_attach(): thread:dhd_watchdog_thread:6d started [ 2.845038] dhd_attach(): thread:dhd_dpc:6e started [ 2.845200] dhd_dpc_thread: set dpc_cpucore 0 from config.txt [ 2.852644] dhd_attach(): thread:dhd_rxf:6f started [ 2.852699] dhd_deferred_work_init: work queue initialized [ 2.888921] Dongle Host Driver, version 1.201.59.6 (r506368) Compiled in drivers/net/wireless/bcmdhd on Jun 30 2017 at 01:13:53 [ 2.889616] Register interface [wlan0] MAC: ac:83:f3:a6:18:90 [ 2.889663] dhdsdio_probe : the lock is released. [ 2.889793] dhd_module_init: Exit err=0 [ 2.907504] systemd-journald[64]: Received request to flush runtime journal from PID 1 [ 2.918492] ambarella-crypto f0020000.crypto: Ambarella Media Processor Cryptography Engine probed(interrupt mode). [ 3.967462] UBI: attaching mtd6 to ubi1 [ 4.029390] UBI: scanning is finished [ 4.042362] UBI: attached mtd6 (name "sec", size 10 MiB) to ubi1 [ 4.042410] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.042450] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.042472] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.042492] UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 [ 4.042511] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.042533] UBI: max/mean erase counter: 13/8, WL threshold: 4096, image sequence number: 2064066047 [ 4.042560] UBI: available PEBs: 11, total reserved PEBs: 69, PEBs reserved for bad PEB handling: 40 [ 4.044034] UBI: background thread "ubi_bgt1d" started, PID 163 [ 4.119374] UBIFS: background thread "ubifs_bgt1_0" started, PID 166 [ 4.190712] UBIFS: mounted UBI device 1, volume 0, name "usr-c" [ 4.190763] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.191549] UBIFS: FS size: 2031616 bytes (1 MiB, 16 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs) [ 4.191592] UBIFS: reserved for root: 95957 bytes (93 KiB) [ 4.191619] UBIFS: media format: w4/r0 (latest is w4/r0), UUID D100E21E-2DE7-442A-9E78-59ABA27A2D51, small LPT model [ 4.890877] SYSCLK:SO[24000000] [ 4.911150] VIN: OV9750 init(2-lane mipi) [ 5.101396] SSID available [ 5.138170] Starting mcu_daemon.sh [ 5.162898] mcu_daemon.sh: locking [ 7.849004] mcu_update: 'f6412eb3' | 'f6412eb3' [ 7.850525] mcu_daemon ready [ 7.863823] mcu_daemon.sh: unlocked [ 8.601088] mars_led.sh locked [ 8.633423] mars_led.sh unlocked [ 8.673952] mars_led.sh locked [ 8.687235] mars_led.sh unlocked [ 8.720376] dhd_open: Enter 889ccc00 [ 8.720762] dhd_conf_read_roam_params: roam_off = 1 [ 8.721578] dhd_conf_read_roam_params: roam_off_suspend = 1 [ 8.721791] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/broadcom/ap6234/fw_bcm43341b0_ag.bin [ 8.721804] dhdsdio_download_firmware: set use_rxchain 1 from config.txt [ 8.721811] Final fw_path=/lib/firmware/broadcom/ap6234/fw_bcm43341b0_ag.bin [ 8.721817] Final nv_path=/lib/firmware/broadcom/ap6234/nvram_ap6234_tcpka.txt [ 8.721823] Final conf_path=/lib/firmware/broadcom/ap6234/bcmdhd.cal [ 8.902201] NVRAM version: AP6234_NVRAM_V1.1_20131225 [ 8.911476] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 9.071796] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 9.074132] dhd_conf_set_band: Set band 0 [ 9.074357] dhd_preinit_ioctls: Set tcpack_sup_mode 0 [ 9.076492] Firmware up: op_mode=0x0015, MAC=ac:83:f3:a6:18:90 [ 9.076511] dhd_conf_set_country: Set country US, revision 0 [ 9.151070] Country code: US (US/0) [ 9.151452] dhd_conf_set_roam: Set roam_off 1 [ 9.162111] Firmware version = wl0: Jul 27 2015 18:57:58 version 6.10.191.wowl.5 (B0 Station/P2P) FWID 01-79c8a2fd es4.c3 [ 9.162135] Driver: 1.201.59.6 (r506368) Firmware: wl0: Jul 27 2015 18:57:58 version 6.10.191.wowl.5 (B0 Station/P2P) FWID 01-79c8a2fd es4.c3 [ 9.162151] dhd_txglom_enable: enable 0 [ 9.162159] dhd_conf_set_disable_proptx: set disable_proptx 0 [ 9.168971] dhd_preinit_ioctls wl ampdu_hostreorder failed -23 [ 9.203844] dhd_open: Exit ret=0 [ 11.469694] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 12.409704] Bluetooth: Core ver 2.16 [ 12.411294] NET: Registered protocol family 31 [ 12.411315] Bluetooth: HCI device and connection manager initialized [ 12.411353] Bluetooth: HCI socket layer initialized [ 12.411370] Bluetooth: L2CAP socket layer initialized [ 12.411424] Bluetooth: SCO socket layer initialized [ 12.424354] Bluetooth: HCI UART driver ver 2.2 [ 12.424378] Bluetooth: HCI H4 protocol initialized [ 12.424385] Bluetooth: HCI BCSP protocol initialized [ 12.424391] Bluetooth: HCILL protocol initialized [ 12.424397] Bluetooth: HCI Three-wire UART (H5) protocol initialized [ 18.303833] Connectting with 6c:70:9f:dc:62:5a channel (1) ssid "TUFFNET2", len (8) [ 18.316979] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 18.320472] cfg80211: Calling CRDA for country: US [ 18.320602] CFG80211-ERROR) wl_cfg80211_reg_notifier : Set country code US from 11d AP [ 18.322869] cfg80211: Regulatory domain changed to country: US [ 18.322890] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 18.322903] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (3000 mBi, 0 mBm) [ 18.322912] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 18.322920] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 18.322928] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2300 mBi, 0 mBm) [ 18.322936] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (3000 mBi, 0 mBm) [ 18.322945] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (4000 mBi, 0 mBm) [ 18.388206] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 20.917102] wlan0 Link encap:Ethernet HWaddr AC:83:F3:A6:18:90 inet addr:10.0.1.28 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1643 (1.6 KiB) TX bytes:1640 (1.6 KiB) [ 20.955233] mars_led.sh locked [ 20.962140] mars_led.sh unlocked [ 22.538707] nl_process_session_cmd(165): NETLINK DBG: Correct connect cmd from app 428. [ 22.538737] nl_send_msg(125): NETLINK DBG: Send session status 0 to session cmd 0 of app 428. [ 23.292505] iav_goto_idle(935): Goto Idle from STATE_INIT. [ 23.292527] dsp_set_op_mode(449): [debug]: dsp_set_op_mode: dsp->op_mode(3), op_mode(0) [ 23.292541] __reset_vin(219): dsp reset vin [ 23.297907] dsp_set_op_mode(472): Entering DSP mode [0]... [ 23.332997] dsp_set_op_mode(480): [Done] Entered mode [0]. [ 26.411538] iav_check_vout(653): VOUT are all disabled. [ 26.411604] check_dsp_mem_bandwidth(972): S2L chip ID [1], DSP memory bandwidth [113 MB/s], limit [1148 MB/s]. [ 26.411620] check_dsp_mem_size(1175): DSP DRAM size used [34 MB], limit [81 MB]. [ 26.411653] nl_send_msg(104): NETLINK DBG: Send request cmd 2 to app 428. [ 26.482296] nl_process_request_status(219): NETLINK DBG: Request 2 succeeded from app 428. [ 26.482413] dsp_set_enc_sub_mode(427): Entering DSP ENC sub mode [2] [ 26.632727] handle_enc_msg(210): DSP DRAM Used: 34 MB, Limited: 81 MB [ 26.632766] dsp_set_enc_sub_mode(434): [Done] Entered sub mode. [ 26.634540] calc_frame_rate(333): idsp out fps 17066667 (scan format: 0, den_encode_fps: 1000), encode fps 30000 [ 26.702085] nl_send_msg(104): NETLINK DBG: Send request cmd 0 to app 428. [ 26.766608] nl_process_request_status(219): NETLINK DBG: Request 0 succeeded from app 428. [ 26.767018] iav_enable_preview(830): preview enabled. [ 26.902126] iav_ioc_start_encode(1519): Wait 4 frames before encode for encode start delay. [ 26.902154] check_encode_resource_limit(807): Check encode resource limit : VIN [30], system load 36000. [ 26.902176] check_dsp_mem_bandwidth(972): S2L chip ID [1], DSP memory bandwidth [168 MB/s], limit [1148 MB/s]. [ 26.902190] check_dsp_mem_size(1175): DSP DRAM size used [34 MB], limit [81 MB]. [ 26.902203] iav_ioc_start_encode(1530): Init encoder when start encoding from preview state. [ 26.902270] calc_frame_rate(333): idsp out fps 17066667 (scan format: 0, den_encode_fps: 1000), encode fps 30000 [ 26.902289] calc_frame_rate(333): idsp out fps 17066667 (scan format: 0, den_encode_fps: 1000), encode fps 30000 [ 27.016837] check_encode_resource_limit(807): Check encode resource limit : VIN [30], system load 36000. [ 27.017159] check_encode_resource_limit(807): Check encode resource limit : VIN [30], system load 36000. [ 27.535883] calc_frame_rate(333): idsp out fps 34133333 (scan format: 0, den_encode_fps: 1000), encode fps 15000 [ 29.052700] nl_process_session_cmd(165): NETLINK DBG: Correct connect cmd from app 575. [ 29.052730] nl_send_msg(125): NETLINK DBG: Send session status 0 to session cmd 0 of app 575. [ 757.293041] CFG80211-ERROR) wl_cfg80211_disconnect : Reason 3 [ 757.295988] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_LINK [ 757.296017] link down if wlan0 may call cfg80211_disconnected. event : 16, reason=2 from 6c:70:9f:dc:62:5a [ 757.308077] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_DEAUTH [ 757.309580] cfg80211: Calling CRDA to update world regulatory domain [ 757.313036] CFG80211-ERROR) wl_cfg80211_reg_notifier : reg_notifier for intiator:0 not supported : set default [ 757.313060] CFG80211-ERROR) wl_cfg80211_reg_notifier : Set country code 00 from User [ 757.323140] WLDEV-ERROR) wldev_set_country : wldev_set_country: set country for 00 as 00 rev -1 failed [ 757.323168] CFG80211-ERROR) wl_cfg80211_reg_notifier : set country Failed :-2 [ 757.323178] cfg80211: World regulatory domain updated: [ 757.323187] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 757.323198] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (2000 mBi, 0 mBm) [ 757.323207] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 757.323215] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 757.323223] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 757.323231] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 757.323239] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2000 mBi, 0 mBm) [ 757.323247] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 757.323256] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 757.323933] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 760.633788] Connectting with 6c:70:9f:dc:62:5a channel (1) ssid "TUFFNET2", len (8) [ 760.647485] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 760.652425] cfg80211: Calling CRDA for country: US [ 760.652651] CFG80211-ERROR) wl_cfg80211_reg_notifier : Set country code US from 11d AP [ 760.655175] cfg80211: Regulatory domain changed to country: US [ 760.655196] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 760.655208] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (3000 mBi, 0 mBm) [ 760.655217] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 760.655226] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 760.655234] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2300 mBi, 0 mBm) [ 760.655243] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (3000 mBi, 0 mBm) [ 760.655251] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (4000 mBi, 0 mBm) [ 760.694818] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 763.197166] mars_led.sh locked [ 763.262537] mars_led.sh unlocked [ 763.543290] mars_led.sh locked [ 763.635625] mars_led.sh unlocked [ 767.321784] CFG80211-ERROR) wl_cfg80211_disconnect : Reason 3 [ 767.324382] CFG80211-ERROR) wl_is_linkdown : Link down Reason : WLC_E_LINK [ 767.324413] link down if wlan0 may call cfg80211_disconnected. event : 16, reason=2 from 6c:70:9f:dc:62:5a [ 767.328355] cfg80211: Calling CRDA to update world regulatory domain [ 767.328443] CFG80211-ERROR) wl_cfg80211_reg_notifier : reg_notifier for intiator:0 not supported : set default [ 767.328458] CFG80211-ERROR) wl_cfg80211_reg_notifier : Set country code 00 from User [ 767.330587] WLDEV-ERROR) wldev_set_country : wldev_set_country: set country for 00 as 00 rev -1 failed [ 767.330614] CFG80211-ERROR) wl_cfg80211_reg_notifier : set country Failed :-2 [ 767.330624] cfg80211: World regulatory domain updated: [ 767.330633] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 767.330644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (2000 mBi, 0 mBm) [ 767.330654] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 767.330662] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (2000 mBi, 0 mBm) [ 767.330670] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 767.330678] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 767.330686] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2000 mBi, 0 mBm) [ 767.330694] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (2000 mBi, 0 mBm) [ 767.330703] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 767.331496] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 770.722845] Connectting with 6c:70:9f:dc:62:5a channel (1) ssid "TUFFNET2", len (8) [ 770.739295] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 770.743780] cfg80211: Calling CRDA for country: US [ 770.743914] CFG80211-ERROR) wl_cfg80211_reg_notifier : Set country code US from 11d AP [ 770.745461] cfg80211: Regulatory domain changed to country: US [ 770.745481] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 770.745493] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (3000 mBi, 0 mBm) [ 770.745502] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 770.745511] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (2300 mBi, 0 mBm) [ 770.745519] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (2300 mBi, 0 mBm) [ 770.745527] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (3000 mBi, 0 mBm) [ 770.745536] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (4000 mBi, 0 mBm) [ 770.832492] wl_bss_connect_done succeeded with 6c:70:9f:dc:62:5a [ 773.480276] wlan0 Link encap:Ethernet HWaddr AC:83:F3:A6:18:90 inet addr:10.0.1.47 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1323 errors:0 dropped:0 overruns:0 frame:0 TX packets:901 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:400733 (391.3 KiB) TX bytes:355255 (346.9 KiB) [ 773.532254] mars_led.sh locked [ 773.543561] mars_led.sh unlocked [14650.116131] calc_frame_rate(333): idsp out fps 17066667 (scan format: 0, den_encode_fps: 1000), encode fps 30000